Printed values, calculations, image traces and observed counts are different kinds of evidence. “Verified” applies to the specific reading—not to the whole room or model.
f1-elevator-doors-1-2-w217-detailverified · observed
source_sheet_identity
sheet-W217IMG_1095 prints W217 in its title block. Its Bay P elevator elevation and IMG_1097 share the same indicator legend B 1 2 3 4 5 6 7, MODEL NO. 32/33/34 marks, ornamental jambs, panel layout, dimension chains and section-E markers. IMG_1097 is therefore a detail photograph of W217, not merely a subject match. Authoring eligibility: eligible-source-attribution.
f1-elevator-doors-1-2-w217-detailverified · observed
printed_width_dimension_endpoints
inside face of left 6-inch ornamental jamb to inside face of right 6-inch ornamental jambThe 3'-6" segment is the middle segment of a horizontal chain. Its extension lines align with the two inner jamb faces. The adjacent 6-inch segments measure the ornamental jambs. The 3'-6" value is not an outer-frame, outer-ornament, rough-opening, or individual-leaf dimension. Authoring eligibility: eligible-endpoint-interpretation. Missing: Whether the fully opened elevator equipment preserves the entire finished-jamb width as operating clear width.
f1-elevator-doors-1-2-w217-detailverified · observed
printed_height_dimension_endpoints
finished floor/sill baseline to underside of door head at the bottom of the position-indicator bandThe vertical chain is drawn on the entrance centerline. Its lower endpoint is the finished floor/sill baseline and its upper endpoint is the horizontal head line immediately below the ELEVATOR POSITION INDICATOR band. It does not run to the top of the ornamental surround. Authoring eligibility: eligible-endpoint-interpretation. Missing: Sill and head section needed to classify the dimension as operating clear height rather than finished entrance-envelope height.
f1-elevator-doors-1-2-w217-detailverified · printed
door_material_description
metal elevator doors with cast ornamentMetal is generic; the sheet does not name an alloy, gauge, finish, backing construction or leaf thickness.
f1-elevator-doors-1-2-w217-detailverified · observed
observed_door_face_panel_layout
{"rows":5,"panelsPerRow":2,"observedTotal":10,"patternClassSequenceTopToBottom":["A","B","A","B","A"]}Five aligned pairs of square outer panel frames are visible. Pattern classes A and B are neutral visual groupings, not historical motif identifications. Count and alignment do not establish individual leaf construction or panel dimensions.
f1-elevator-doors-1-2-w217-detailunreviewed · observed
leaf count, operating type, direction, travel, overlap, guides and clear-open condition
UnresolvedThe elevation shows two graphic door-face fields and a centerline but no equipment-side mechanics or travel diagram.
IMG_1097 · sheet-W217 · Locate on drawing ↗Drawing notation: CAST METAL ORNAMENT; ELEVATOR POSITION INDICATOR; B 1 2 3 4 5 6 7; 6"; 3'-6"; 6"; 5 1/2"; METAL ELEVATOR DOORS; CAST ORNAMENT.; MODEL NO. 32; MODEL NO. 33; MODEL NO. 34; 7 3/4"; MARBLE PLINTH
f1-elevator-doors-1-2-w217-detailunreviewed · observed
jamb depth, return, projection and section profile
UnresolvedThe 6-inch values are elevation face widths only; Section E is not present in the reviewed close-up as readable construction geometry.
IMG_1097 · sheet-W217 · Locate on drawing ↗Drawing notation: CAST METAL ORNAMENT; ELEVATOR POSITION INDICATOR; B 1 2 3 4 5 6 7; 6"; 3'-6"; 6"; 5 1/2"; METAL ELEVATOR DOORS; CAST ORNAMENT.; MODEL NO. 32; MODEL NO. 33; MODEL NO. 34; 7 3/4"; MARBLE PLINTH
f1-elevator-doors-1-2-w217-detailunreviewed · observed
ornament vector trace, motif identity, thickness, relief depth, repeat pitch and fabrication geometry
UnresolvedThe elevation and material callouts establish visible ornament and generic cast construction, not exact three-dimensional ornament.
IMG_1097 · sheet-W217 · Locate on drawing ↗Drawing notation: CAST METAL ORNAMENT; ELEVATOR POSITION INDICATOR; B 1 2 3 4 5 6 7; 6"; 3'-6"; 6"; 5 1/2"; METAL ELEVATOR DOORS; CAST ORNAMENT.; MODEL NO. 32; MODEL NO. 33; MODEL NO. 34; 7 3/4"; MARBLE PLINTH
f1-elevator-doors-1-2-w217-detailunreviewed · observed
individual panel width, height, frame-layer widths and depth
UnresolvedOnly selected offsets are printed. Panel sizes may not be derived from pixels or by subtracting visually symmetric gaps from the finished envelope.
IMG_1097 · sheet-W217 · Locate on drawing ↗Drawing notation: CAST METAL ORNAMENT; ELEVATOR POSITION INDICATOR; B 1 2 3 4 5 6 7; 6"; 3'-6"; 6"; 5 1/2"; METAL ELEVATOR DOORS; CAST ORNAMENT.; MODEL NO. 32; MODEL NO. 33; MODEL NO. 34; 7 3/4"; MARBLE PLINTH
f1-elevator-doors-1-2-w217-detailunreviewed · observed
application of model 33 or 34 to earlier visually matching panel rows
UnresolvedVisual pattern matching alone does not establish printed model-number applicability.
IMG_1097 · sheet-W217 · Locate on drawing ↗Drawing notation: CAST METAL ORNAMENT; ELEVATOR POSITION INDICATOR; B 1 2 3 4 5 6 7; 6"; 3'-6"; 6"; 5 1/2"; METAL ELEVATOR DOORS; CAST ORNAMENT.; MODEL NO. 32; MODEL NO. 33; MODEL NO. 34; 7 3/4"; MARBLE PLINTH
f1-elevator-doors-1-2-w217-detailunreviewed · observed
rough opening width, height and construction interfaces
UnresolvedThe accepted 3'-6" by 6'-9 3/4" envelope is bounded by finished entrance faces, not rough construction.
IMG_1097 · sheet-W217 · Locate on drawing ↗Drawing notation: CAST METAL ORNAMENT; ELEVATOR POSITION INDICATOR; B 1 2 3 4 5 6 7; 6"; 3'-6"; 6"; 5 1/2"; METAL ELEVATOR DOORS; CAST ORNAMENT.; MODEL NO. 32; MODEL NO. 33; MODEL NO. 34; 7 3/4"; MARBLE PLINTH
f1-elevator-doors-1-2-w217-detailunreviewed · observed
wall-face assignment, local station, world position and world orientation
UnresolvedNo side-chain token was promoted to placement, and no detail-to-plan registration was performed in this package.
IMG_1097 · sheet-W217 · Locate on drawing ↗Drawing notation: CAST METAL ORNAMENT; ELEVATOR POSITION INDICATOR; B 1 2 3 4 5 6 7; 6"; 3'-6"; 6"; 5 1/2"; METAL ELEVATOR DOORS; CAST ORNAMENT.; MODEL NO. 32; MODEL NO. 33; MODEL NO. 34; 7 3/4"; MARBLE PLINTH
f1-elevator-doors-1-2-w217-detailunreviewed · printed
unassigned printed dimension witness
1'-3 3/4"; 1'-1 1/2"These segments extend left of the ornamental jamb into adjacent Bay P work; their complete endpoints and component assignments are outside the close-up. They are not entrance placement controls.
f1-elevator-doors-1-2-w217-detailunreviewed · printed
unassigned printed dimension witness
1'-1 1/2"; 2"; [small fractions partly unreadable]These segments run from the right ornamental jamb into adjacent vertical profile work. The close-up does not securely assign them to entrance components or placement datums.
f1-elevator-doors-1-2-w217-detailunreviewed · printed
unassigned printed dimension witness
4'-11"The token is legible, but its extension line and endpoints do not securely identify an entrance component or axis. It is retained as a witness, not a physical property.
f1-elevator-doors-1-2-w217-detailverified · printed
unassigned_right_elevation_chain_fine_segment
2½″2.5 in
Local segment immediately to the right of the 2-inch witness and below the main chain. Neighboring vertical profile line endpoints are visible, but component/material and complete chain endpoints are unassigned. Not an entrance depth, axis or world-placement control. Installed instance mapping, world placement, companion/revision authority and whole-building acceptance remain unresolved.
IMG_1097 · W-217 · Locate on drawing ↗Drawing notation: 2½″
Local segment immediately to the right of the 2-inch witness and below the main chain. Neighboring vertical profile line endpoints are visible, but component/material and complete chain endpoints are unassigned. Not an entrance depth, axis or world-placement control. Installed instance mapping, world placement, companion/revision authority and whole-building acceptance remain unresolved.