Every dimension belongs to an object and a drawing. Original room numbers, object marks, printed values and source regions stay together—even when the answer is unresolved.
464 of 464 photographs have extraction records, containing 27,517 properties. Initial image review is not exhaustive extraction: 0 photographs have passed the full-region check. 66 numbered sheets are reconciled. Modeling and architectural registration are separate work; these counts do not establish a complete building.
Download the structured register (JSON)Object: W-415 general reinforcement and footing design notes
Printed values, calculations, image traces and observed counts are different kinds of evidence. “Verified” applies to the specific reading—not to the whole room or model.
5000 psf
Printed design rule applies to the depicted sheet/floor assembly; does not establish installed condition or individual exact geometry.
Drawing notation: 5000 #/SQ. FT.
Printed design rule applies to the depicted sheet/floor assembly; does not establish installed condition or individual exact geometry.
36 in
Printed design rule applies to the depicted sheet/floor assembly; does not establish installed condition or individual exact geometry.
Drawing notation: IN SLABS BEND UP ALTERNATE RODS OVER SUPPORTS IN ALL SPANS OVER 3′-0″
Printed design rule applies to the depicted sheet/floor assembly; does not establish installed condition or individual exact geometry.
30 degrees
Printed design rule applies to the depicted sheet/floor assembly; does not establish installed condition or individual exact geometry.
Drawing notation: 30° TO 45°
Printed design rule applies to the depicted sheet/floor assembly; does not establish installed condition or individual exact geometry.
45 degrees
Printed design rule applies to the depicted sheet/floor assembly; does not establish installed condition or individual exact geometry.
Drawing notation: 30° TO 45°
Printed design rule applies to the depicted sheet/floor assembly; does not establish installed condition or individual exact geometry.
0.6 ratio
Printed design rule applies to the depicted sheet/floor assembly; does not establish installed condition or individual exact geometry.
Drawing notation: LESS THAN 6/10 OF THE CLEAR SPAN BETWEEN BOTTOM BENDS
Printed design rule applies to the depicted sheet/floor assembly; does not establish installed condition or individual exact geometry.
180 degrees
Printed design rule applies to the depicted sheet/floor assembly; does not establish installed condition or individual exact geometry.
Drawing notation: AT ENDS OF END SPANS AND SIMPLY SUPPORTED SPANS BEND RODS AT FACE OF SUPPORT WITH 180° HOOKS
Printed design rule applies to the depicted sheet/floor assembly; does not establish installed condition or individual exact geometry.
Numeric value unresolved
Printed design rule applies to the depicted sheet/floor assembly; does not establish installed condition or individual exact geometry.
Drawing notation: MAKE THE TOP BEND AT A DISTANCE FROM THE CENTER OF THE COLUMN EQUAL TO [fraction unresolved] CLEAR SPAN
Printed design rule applies to the depicted sheet/floor assembly; does not establish installed condition or individual exact geometry.
Numeric value unresolved
Printed design rule applies to the depicted sheet/floor assembly; does not establish installed condition or individual exact geometry.
Drawing notation: IF MORE THAN TWO RODS ARE BENT THEY MAY BE BENT AT TWO POINTS NOT MORE THAN [fraction unresolved] EFFECTIVE DEPTH APART
Printed design rule applies to the depicted sheet/floor assembly; does not establish installed condition or individual exact geometry.
3 in
Printed design rule applies to the depicted sheet/floor assembly; does not establish installed condition or individual exact geometry.
Drawing notation: ALL RODS SHALL EXTEND TO WITHIN 3″ OF OUTSIDE FACE OF SUPPORT
Printed design rule applies to the depicted sheet/floor assembly; does not establish installed condition or individual exact geometry.
Printed design rule applies to the depicted sheet/floor assembly; does not establish installed condition or individual exact geometry.
Drawing notation: STIRRUP SPACING IN THE SCHEDULE IS GIVEN CONTINUOUSLY FROM THE FACE OF SUPPORT
Printed design rule applies to the depicted sheet/floor assembly; does not establish installed condition or individual exact geometry.
Printed design rule applies to the depicted sheet/floor assembly; does not establish installed condition or individual exact geometry.
Drawing notation: FRAME ALL FLOORS AT THE PROPER ELEVATIONS TO ALLOW FOR FINISHED FLOORS AS INDICATED ON THE ARCHITECT'S DRAWINGS
Printed design rule applies to the depicted sheet/floor assembly; does not establish installed condition or individual exact geometry.
0.2 ratio
Printed beam reinforcement rule; ratio only, no span or member length calculated.
Drawing notation: MAKE THE TOP BEND AT A DISTANCE FROM THE CENTER OF THE COLUMN EQUAL TO 1/5 CLEAR SPAN
Printed beam reinforcement rule; ratio only, no span or member length calculated.
0.75 ratio
Printed maximum bend-point spacing as fraction of effective depth; no member depth established.
Drawing notation: IF MORE THAN TWO RODS ARE BENT THEY MAY BE BENT AT TWO POINTS NOT MORE THAN 3/4 EFFECTIVE DEPTH APART
Printed maximum bend-point spacing as fraction of effective depth; no member depth established.
Bend angle depends on depth/span ratio. Existing 30°–45° limits reused; this sentence does not print a numerical depth/span threshold.
Drawing notation: IN BEAMS BEND UP BENT RODS AT AN ANGLE OF 30° TO 45° DEPENDING UPON THE RATIO OF DEPTH TO SPAN
Bend angle depends on depth/span ratio. Existing 30°–45° limits reused; this sentence does not print a numerical depth/span threshold.
Source inventory is separate from the floor filters above. Select one drawing to inspect it; no drawing set is preloaded.