Printed values, calculations, image traces and observed counts are different kinds of evidence. “Verified” applies to the specific reading—not to the whole room or model.
main-north-entrance-bronze-rail-run-positive-xunreviewed · derived
Registered lower rail-axis elevation
-7.156667 ft local-7.156667 ft
W213 rail height added to the 83.26 lower surface; not a physical endpoint extension.
IMG_1242 · sheet-W201 · Locate on drawing ↗Drawing notation: HALF PLAN; CENTER LINE OF ENTRANCE; 7'-0"; BRONZE RAIL; SEE DETAIL SH. 213
Supplies two mirrored rail axes, each 7 feet from the entrance centerline, and the stair-following relationship.
IMG_1087 · sheet-W213 · Locate on drawing ↗Drawing notation: HANDRAIL / MAIN ENTRANCE STEPS; DOUBLE RAIL; MODEL NO. 10; 2'-10"
Supplies the printed rail height and local fabrication identity; it does not supply the project path.
Calculated from: main-north-steps-lower-elevation, frame-first-floor-finish, main-north-w213-rail-height
main-north-entrance-bronze-rail-run-positive-xunreviewed · derived
Registered lower run endpoint Z
109.575886 ft109.575886 ft
Analytical axis endpoint only.
IMG_1242 · sheet-W201 · Locate on drawing ↗Drawing notation: HALF PLAN; CENTER LINE OF ENTRANCE; 7'-0"; BRONZE RAIL; SEE DETAIL SH. 213
Supplies two mirrored rail axes, each 7 feet from the entrance centerline, and the stair-following relationship.
IMG_1087 · sheet-W213 · Locate on drawing ↗Drawing notation: HANDRAIL / MAIN ENTRANCE STEPS; DOUBLE RAIL; MODEL NO. 10; 2'-10"
Supplies the printed rail height and local fabrication identity; it does not supply the project path.
Calculated from: main-north-w3-bottom-center-world-x, main-north-w3-bottom-center-world-z, main-north-w201-rail-half-offset
detail-img1087-handrailverified · printed
grille-casting-finish
GRILLES FOR WINDOW OPENINGS ONLY SHALL HAVE THESE ORNAMENTAL CASTINGS FINISHED ON BOTH FACESSource-local additive detail review; no installed quantity, accepted room geometry, physical placement or wall cuts established.
IMG_1087 · W-213 · Locate on drawing ↗Drawing notation: GRILLES FOR WINDOW OPENINGS ONLY SHALL HAVE THESE ORNAMENTAL CASTINGS FINISHED ON BOTH FACES
Source-local additive detail review; no installed quantity, accepted room geometry, physical placement or wall cuts established.
detail-img1087-handrailverified · printed
stanchion-bearing
UNDER SIDE OF CASTING TO BE SHAPED TO FIT WASH ON STONESource-local additive detail review; no installed quantity, accepted room geometry, physical placement or wall cuts established.
IMG_1087 · W-213 · Locate on drawing ↗Drawing notation: UNDER SIDE OF CASTING TO BE SHAPED TO FIT WASH ON STONE
Source-local additive detail review; no installed quantity, accepted room geometry, physical placement or wall cuts established.
detail-img1087-handrailverified · printed
grille-material
WROUGHT METALSource-local additive detail review; no installed quantity, accepted room geometry, physical placement or wall cuts established.
IMG_1087 · W-213 · Locate on drawing ↗Drawing notation: WROUGHT METAL
Source-local additive detail review; no installed quantity, accepted room geometry, physical placement or wall cuts established.
detail-img1087-handrailverified · printed
grille-model-mark
MODEL No.1212 model-number
Source-local additive detail review; no installed quantity, accepted room geometry, physical placement or wall cuts established.
IMG_1087 · W-213 · Locate on drawing ↗Drawing notation: MODEL No.12
Source-local additive detail review; no installed quantity, accepted room geometry, physical placement or wall cuts established.
metal1012h-img1087-grille-specimenverified · printed
window_grille_casting_material
CAST IRON ON WINDOW GRILLESTargeted crop reads explicit window applicability; does not establish metal of each ornamental casting separately.
IMG_1087 · W-213 · Locate on drawing ↗Drawing notation: CAST IRON ON WINDOW GRILLES
Targeted crop reads explicit window applicability; does not establish metal of each ornamental casting separately.
metal1012h-img1087-grille-specimenverified · printed
bronze_door_grille_shape_fabrication
EXTRUDED SHAPES ON BRONZE DOOR GRILLESPaired construction note distinguishes bronze door shapes from window cast iron. No thickness or alloy specification.
IMG_1087 · W-213 · Locate on drawing ↗Drawing notation: EXTRUDED SHAPES ON BRONZE DOOR GRILLES
Paired construction note distinguishes bronze door shapes from window cast iron. No thickness or alloy specification.
metal1012h-img1087-grille-specimenverified · printed
intersection_rosette_fabrication
CAST ROSETTESLeader connects square decorative intersections to cast-rosette label; attachment and alloy remain null.
metal1012h-img1087-grille-specimenverified · printed
lower_ornamental_panel_construction
SOLID CASTINGSection leader points to lower ornamental panel casting; physical depth and alloy unresolved.
metal1012h-img1087-grille-specimenverified · observed
grille-plan-casting-relationship
CASTING / PLANPrinted source-local type/component or section control only; no accepted physical geometry, installed quantity or world registration. Original layer retained separately from revisions. Plan leader identifies the transverse casting between the two drawn upright member profiles; no member width/depth or installed component count established.
IMG_1087 · W-213 · Locate on drawing ↗Drawing notation: CASTING / PLAN
Printed source-local type/component or section control only; no accepted physical geometry, installed quantity or world registration. Original layer retained separately from revisions. Plan leader identifies the transverse casting between the two drawn upright member profiles; no member width/depth or installed component count established.
main-north-entrance-bronze-rail-baluster-postverified · printed
fork_rail_connection_screw_annotation
R.H. BRONZE SCREWSEND leader addresses screw/circular connection zones immediately below the two rail ends on fork arms. This is a local screw annotation, separate from COUNTERSUNK BRONZE MACHINE SCREWS 12 inches O.C. along the inclined rail. R.H. is preserved literally; diameter, thread, count and exact head geometry remain unresolved.
IMG_1087 · sheet-W213 · Locate on drawing ↗Drawing notation: R.H. BRONZE SCREWS
END leader addresses screw/circular connection zones immediately below the two rail ends on fork arms. This is a local screw annotation, separate from COUNTERSUNK BRONZE MACHINE SCREWS 12 inches O.C. along the inclined rail. R.H. is preserved literally; diameter, thread, count and exact head geometry remain unresolved.
main-north-entrance-bronze-rail-anchorageverified · observed
one_foot_one_control_extension_relationship
1'-1"The printed 13-inch numeric token remains reused and unreviewed for manufactured-face applicability. Extension lines in the detail align as stated; neither endpoint securely represents a stone edge, flange edge, installed baluster station or tread nosing. This observation does not promote the old numeric control to verified authoring.
IMG_1087 · sheet-W213 · Locate on drawing ↗Drawing notation: 1'-1"
The printed 13-inch numeric token remains reused and unreviewed for manufactured-face applicability. Extension lines in the detail align as stated; neither endpoint securely represents a stone edge, flange edge, installed baluster station or tread nosing. This observation does not promote the old numeric control to verified authoring.
metalenv1014t-img1087-pipe-stanchionverified · observed
pipe_stanchion_section_passage_count
[two circular pipe passages drawn in STANCHION face]2 detail-component-count
Source-local printed witness only; no accepted physical geometry, installed quantity or source-issue selection. Two drawn tubular passages, larger above smaller, in this specimen only. Nominal/actual diameters and installed quantities remain open.
IMG_1087 · W-213 · Locate on drawing ↗Drawing notation: [two circular pipe passages drawn in STANCHION face]
Source-local printed witness only; no accepted physical geometry, installed quantity or source-issue selection. Two drawn tubular passages, larger above smaller, in this specimen only. Nominal/actual diameters and installed quantities remain open.
metalenv1014t-img1087-pipe-stanchionverified · observed
pipe_stanchion_base_attachment_relationship
[base fixing drawn through flange to lower plate/nut]Source-local printed witness only; no accepted physical geometry, installed quantity or source-issue selection. Observed left-side fixing with upper nut and lower rectangular plate/nut; bolt diameter, plate size and embedment not established.
IMG_1087 · W-213 · Locate on drawing ↗Drawing notation: [base fixing drawn through flange to lower plate/nut]
Source-local printed witness only; no accepted physical geometry, installed quantity or source-issue selection. Observed left-side fixing with upper nut and lower rectangular plate/nut; bolt diameter, plate size and embedment not established.
main-north-entrance-bronze-rail-baluster-postverified · printed
shaft_construction
CAST BRONZE / HOLLOW SHAFTLeader addresses the fluted vertical baluster shaft. Distinct from the solid forked piece, steel core bolt and property-line stanchion.
IMG_1087 · W-213 · Locate on drawing ↗Drawing notation: CAST BRONZE / HOLLOW SHAFT
Leader addresses the fluted vertical baluster shaft. Distinct from the solid forked piece, steel core bolt and property-line stanchion.
main-north-entrance-bronze-railunreviewed · observed
individual_rail_member_profile_width
[no secure printed member width in reviewed END/side crop]Numeric value unresolved
END draws two shaped open/capped member ends carried by bifurcated head. The existing 7½+7½ axis pitch is not either member's profile width.
IMG_1087 · W-213 · Locate on drawing ↗Drawing notation: [no secure printed member width in reviewed END/side crop]
END draws two shaped open/capped member ends carried by bifurcated head. The existing 7½+7½ axis pitch is not either member's profile width.
main-north-entrance-bronze-rail-baluster-postunreviewed · observed
hollow_post_outside_profile_width
[no secure printed shaft outside width in reviewed crop]Numeric value unresolved
Neither steel bolt diameter, 6½-inch paired base controls nor page-scale pixel width establishes the hollow bronze shaft section.
IMG_1087 · W-213 · Locate on drawing ↗Drawing notation: [no secure printed shaft outside width in reviewed crop]
Neither steel bolt diameter, 6½-inch paired base controls nor page-scale pixel width establishes the hollow bronze shaft section.
main-north-entrance-bronze-rail-baluster-postverified · observed
end_view_fork_member_relationship
END / DOUBLE RAILEND view shows two ornamental arms bifurcating from one central baluster, each supporting one rail member. Two member axes within a run remain distinct from the two mirrored runs on W201.
IMG_1087 · W-213 · Locate on drawing ↗Drawing notation: END / DOUBLE RAIL
END view shows two ornamental arms bifurcating from one central baluster, each supporting one rail member. Two member axes within a run remain distinct from the two mirrored runs on W201.